Scanning the outside of a ranch home in Longmont , Colo.
But you don’t need an infrared camera to reveal utility-bill busters that are left after the obvious stuff is done. You need the right point of view. Big energy leaks are often hiding in plain sight, and many of them are easy to fix—you may not even need tools. Here’s how to get started.
But you don’t need an infrared camera to reveal utility-bill busters that are left after the obvious stuff is done. You need the right point of view. Big energy leaks are often hiding in plain sight, and many of them are easy to fix—you may not even need tools. Here’s how to get started.
ELECTRONICS & APPLIANCES
For gaps in ducts over 18 in. wide, apply mesh duct-sealing tape across the gap (A). Next, brush a generous amount of duct mastic over the tape using a disposable paintbrush (B). For narrower gaps or seams, use the mastic alone. (Illustration by Gabriel Silveira)
Put away the duct tape. You need a better seal. Between 25 and 40 percent of the hot and cold air entering ducts escapes through joints, seams and gaps—many covered with poorly applied tape. That’s hard-earned money disappearing. Cut your losses by sealing duct joints with mastic, a paint-on putty, and patch holes with aluminum tape. If supply ducts have insulation, peel it back to seal the collars. Pay particular attention to elbows, advises Iowa Energy’s McAnally. “That’s where pressure builds and the air wants out,” he says. And don’t neglect return ducts. Leaks in returns strain your HVAC system and can cause pressure differentials that result in hot summer air or cold winter air being sucked into the house. Cost: $40 | Monthly Savings: $9.33 | Payback: 4 months
+ Program the Thermostat
Install an Energy Star–qualified programmable thermostat that automatically adjusts heating and cooling temperatures based on a daily heating or cooling schedule.
For every degree you push the thermostat beyond your usual set points, you save an additional 2 percent on utility charges. Some utilities, such as Austin Energy in
+ Keep A/C Filters and Coils Clean
A dirty air filter reduces airflow, and a dirty condenser coil retains heat and is less efficient. The two can increase the system’s power consumption by 10 percent or more. Clean the condenser coil every two years and change filters monthly during peak cooling and heating seasons. Cost: $50 | Monthly Savings: $8.33 | Payback: 6 months
+ Catch a Breeze
Ceiling fans minimize the need for air conditioning in summer, or at least allow you to nudge the thermostat up a few degrees, and they enhance winter comfort. Cost: $100 | Monthly Savings: $1.33 | Payback: 6.5 years
+ Add Humidity
Dry air retains less heat and feels cooler against the skin. Increase ambient humidity with a humidifier this winter, and edge the thermostat down a degree or two. Cost: $72, for three humidifiers | Monthly Savings: $3.85 | Payback: 1.5 years
PLUMBING
For gaps in ducts over 18 in. wide, apply mesh duct-sealing tape across the gap (A). Next, brush a generous amount of duct mastic over the tape using a disposable paintbrush (B). For narrower gaps or seams, use the mastic alone. (Illustration by Gabriel Silveira)
Put away the duct tape. You need a better seal. Between 25 and 40 percent of the hot and cold air entering ducts escapes through joints, seams and gaps—many covered with poorly applied tape. That’s hard-earned money disappearing. Cut your losses by sealing duct joints with mastic, a paint-on putty, and patch holes with aluminum tape. If supply ducts have insulation, peel it back to seal the collars. Pay particular attention to elbows, advises Iowa Energy’s McAnally. “That’s where pressure builds and the air wants out,” he says. And don’t neglect return ducts. Leaks in returns strain your HVAC system and can cause pressure differentials that result in hot summer air or cold winter air being sucked into the house. Cost: $40 | Monthly Savings: $9.33 | Payback: 4 months
+ Program the Thermostat
Install an Energy Star–qualified programmable thermostat that automatically adjusts heating and cooling temperatures based on a daily heating or cooling schedule.
For every degree you push the thermostat beyond your usual set points, you save an additional 2 percent on utility charges. Some utilities, such as Austin Energy in
+ Keep A/C Filters and Coils Clean
A dirty air filter reduces airflow, and a dirty condenser coil retains heat and is less efficient. The two can increase the system’s power consumption by 10 percent or more. Clean the condenser coil every two years and change filters monthly during peak cooling and heating seasons. Cost: $50 | Monthly Savings: $8.33 | Payback: 6 months
+ Catch a Breeze
Ceiling fans minimize the need for air conditioning in summer, or at least allow you to nudge the thermostat up a few degrees, and they enhance winter comfort. Cost: $100 | Monthly Savings: $1.33 | Payback: 6.5 years
+ Add Humidity
Dry air retains less heat and feels cooler against the skin. Increase ambient humidity with a humidifier this winter, and edge the thermostat down a degree or two. Cost: $72, for three humidifiers | Monthly Savings: $3.85 | Payback: 1.5 years
PLUMBING
sheetmetal around chimney flues and combustion vents. Cost: $75 in materials | Monthly Savings: $15 | Payback: 5 months
YEARLY NO-COST ENERGY SLASHERS PLUMBING
+ Throttle Back Showers
Showers account for 26 percent of a household’s hot-water use. Installing a low-flow shower head can shrink that flood from 3.5 gal. per minute to 1.5 gal.
Cost: $9, for two no-frills, 1.5-gal./minute heads | Monthly Savings: $15 | Payback: 3 weeks
+ Slow the Flow
A faucet aerator can save 400 gal. of hot water a year. Translation: less work for the water heater. If the rated flow on your current aerator is visible, and if it’s above 2.75 gal./minute, then replace it with a more efficient model that emits 1.5 gal./minute or less. If the aerator’s flow rate has been scuffed off or it’s too hard to read, just replace it. The new aerator will likely have lower flow.
Cost: $4.80 for three aerators | Monthly Savings: $0.93 | Payback: 5 months
+ Stop Drips
A slow leak of 10 drips per minute from a hot-water faucet wastes 526 gal. a year, or about the equivalent of emptying and refilling a 40-gal. water heater 13 times. Swapping in a new washer or O-ring is an easy fix, even for a novice DIYer.
Cost: $1 | Monthly Savings: $0.35 | Payback: 3 months
+ Throttle Back Showers
Showers account for 26 percent of a household’s hot-water use. Installing a low-flow shower head can shrink that flood from 3.5 gal. per minute to 1.5 gal.
Cost: $9, for two no-frills, 1.5-gal./minute heads | Monthly Savings: $15 | Payback: 3 weeks
+ Slow the Flow
A faucet aerator can save 400 gal. of hot water a year. Translation: less work for the water heater. If the rated flow on your current aerator is visible, and if it’s above 2.75 gal./minute, then replace it with a more efficient model that emits 1.5 gal./minute or less. If the aerator’s flow rate has been scuffed off or it’s too hard to read, just replace it. The new aerator will likely have lower flow.
Cost: $4.80 for three aerators | Monthly Savings: $0.93 | Payback: 5 months
+ Stop Drips
A slow leak of 10 drips per minute from a hot-water faucet wastes 526 gal. a year, or about the equivalent of emptying and refilling a 40-gal. water heater 13 times. Swapping in a new washer or O-ring is an easy fix, even for a novice DIYer.
Cost: $1 | Monthly Savings: $0.35 | Payback: 3 months
+ Wash only full loads in dishwashers and washing machines: Save $51
+ Turn the water heater down to 120 degrees from 140: Save $22
+ Remove room air conditioners during winter: Save $40
+ Use Energy Saver features on dishwashers, dryers, fridges and freezers: Save $21
+ Wash clothes in cold water: Save $33
+ Air-dry clothes during the warmest six months: Save $57
+ Turn the water heater down to 120 degrees from 140: Save $22
+ Remove room air conditioners during winter: Save $40
+ Use Energy Saver features on dishwashers, dryers, fridges and freezers: Save $21
+ Wash clothes in cold water: Save $33
+ Air-dry clothes during the warmest six months: Save $57
Showers account for 26 percent of a household’s hot-water use. Installing a low-flow shower head can shrink that flood from 3.5 gal. per minute to 1.5 gal. Cost: $9, for two no-frills, 1.5-gal./minute heads | Monthly Savings: $15 | Payback: 3 weeks
+ Slow the Flow
A faucet aerator can save 400 gal. of hot water a year. Translation: less work for the water heater. If the rated flow on your current aerator is visible, and if it’s above 2.75 gal./minute, then replace it with a more efficient model that emits 1.5 gal./minute or less. If the aerator’s flow rate has been scuffed off or it’s too hard to read, just replace it. The new aerator will likely have lower flow. Cost: $4.80 for three aerators | Monthly Savings: $0.93 | Payback: 5 months
+ Stop Drips
A slow leak of 10 drips per minute from a hot-water faucet wastes 526 gal. a year, or about the equivalent of emptying and refilling a 40-gal. water heater 13 times. Swapping in a new washer or O-ring is an easy fix, even for a novice DIYer. Cost: $1 | Monthly Savings: $0.35 | Payback: 3 months + Throttle Back Showers
Showers account for 26 percent of a household’s hot-water use. Installing a low-flow shower head can shrink that flood from 3.5 gal. per minute to 1.5 gal. Cost: $9, for two no-frills, 1.5-gal./minute heads | Monthly Savings: $15 | Payback: 3 weeks
+ Slow the Flow
A faucet aerator can save 400 gal. of hot water a year. Translation: less work for the water heater. If the rated flow on your current aerator is visible, and if it’s above 2.75 gal./minute, then replace it with a more efficient model that emits 1.5 gal./minute or less. If the aerator’s flow rate has been scuffed off or it’s too hard to read, just replace it. The new aerator will likely have lower flow. Cost: $4.80 for three aerators | Monthly Savings: $0.93 | Payback: 5 months
+ Stop Drips
A slow leak of 10 drips per minute from a hot-water faucet wastes 526 gal. a year, or about the equivalent of emptying and refilling a 40-gal. water heater 13 times. Swapping in a new washer or O-ring is an easy fix, even for a novice DIYer. Cost: $1 | Monthly Savings: $0.35 | Payback: 3 months + Unplug the beer fridge
That old clunker of a refrigerator in the basement could be costing the equivalent of 10 cases of Bud in wasted energy each year. A refrigerator built in 1993 gobbles twice as much energy as new models. Need more cold brew for a party? Plug in the fridge the night before. Cost: $0 | Monthly Savings: $12.50 | Payback: Immediate
+ Plug the Power Drain
As much as 75 percent of electricity use by electronics occurs while the devices are off. Big-screen TVs, stereo systems and computer peripherals are some of the worst offenders. Curtail the loss with power strips that kill power when they sense inactivity. Cost: $115 | Monthly Savings: $3 | Payback: 3 years
+ Give the Sump Pump a Break
A 0.5-hp sump pump can use $30 a month in electricity during wet spring months, estimates Bill McAnally, an advisor to the Iowa Energy Center and an instructor in energy-efficient building. “You’re better off extending downspouts another 5 ft. into the yard to move rainwater away from the basement,” he says. Cost: $16 | Monthly Savings: $6.25 | Payback: 2.5 months
+ Maximize CFLs or LED
We’ve all heard the advice to switch to CFLs. To get the maximum bang for your CFL buck, install the bulbs for their rated use, which will help them last longer. For example, use bulbs that are designed for down-facing, enclosed receptacles in ceiling lights. Other CFLs are rated for use in fixtures plugged into a timer. Also, for a more rapid return on investment, use CFLs in fixtures that are on for at least 3 hours a day. Cost: $3.22 per 15-watt CFL | Monthly Savings: $0.57 | Payback: 6 months
No comments:
Post a Comment